#ifndef Arduino_h
#define Arduino_h

#include <stdbool.h>
#include <stdint.h>
#include <stdlib.h>
#include <string.h>
#include <math.h>

typedef bool boolean;
typedef uint8_t byte;
typedef uint16_t word;

// some libraries and sketches depend on this AVR stuff,
// assuming Arduino.h or WProgram.h automatically includes it...

#include "avr/pgmspace.h"
#include "avr/interrupt.h"

#include "itoa.h"

#ifdef __cplusplus
extern "C"{
#endif // __cplusplus

#include "wiring_constants.h"

#define clockCyclesPerMicrosecond() ( SystemCoreClock / 1000000L )
#define clockCyclesToMicroseconds(a) ( ((a) * 1000L) / (SystemCoreClock / 1000L) )
#define microsecondsToClockCycles(a) ( (a) * (SystemCoreClock / 1000000L) )

void yield( void ) ;

/* sketch */
void setup( void ) ;
void loop( void ) ;

void suspendLoop(void);
uint32_t setLoopStacksize(void);

#include "WVariant.h"

#ifdef __cplusplus
} // extern "C"
#endif

// RTOS
#include "rtos.h"

// The following headers are for C++ only compilation
#ifdef __cplusplus
  #include "WCharacter.h"
  #include "WString.h"
  // #include "Tone.h"
  #include "WMath.h"
  #include "HardwareSerial.h"
  #include "pulse.h"
  #include "HardwarePWM.h"
  #include "utility/SoftwareTimer.h"

  #include "Uart.h"
#endif

#include "delay.h"
#include "binary.h"
#include "common_inc.h"
#include "utility/debug.h"
#include "utility/utilities.h"
#include "utility/AdaCallback.h"

#ifdef NRF52840_XXAA
  #include "tusb.h"

#ifdef __cplusplus
  #include "USBSerial.h"
#endif

#endif

// Include board variant
#include "variant.h"

#include "wiring.h"
#include "wiring_digital.h"
#include "wiring_analog.h"
#include "wiring_shift.h"
#include "WInterrupts.h"

#ifndef __cplusplus
// undefine stdlib's abs if encountered
#ifdef abs
#undef abs
#endif // abs

#define min(a,b) ((a)<(b)?(a):(b))
#define max(a,b) ((a)>(b)?(a):(b))
#define abs(x) ((x)>0?(x):-(x))
#endif // __cplusplus

#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))
#define round(x)     ((x)>=0?(long)((x)+0.5):(long)((x)-0.5))
#define radians(deg) ((deg)*DEG_TO_RAD)
#define degrees(rad) ((rad)*RAD_TO_DEG)
#define sq(x) ((x)*(x))

#define interrupts() __enable_irq()
#define noInterrupts() __disable_irq()

#define lowByte(w) ((uint8_t) ((w) & 0xff))
#define highByte(w) ((uint8_t) ((w) >> 8))

#define bitRead(value, bit) (((value) >> (bit)) & 0x01ul)
#define bitSet(value, bit) ((value) |= (1UL << (bit)))
#define bitClear(value, bit) ((value) &= ~(1UL << (bit)))
#define bitWrite(value, bit, bitvalue) (bitvalue ? bitSet(value, bit) : bitClear(value, bit))

#define bit(b) (1UL << (b))

#ifdef NRF_P1
#define digitalPinToPort(P)        ( (g_ADigitalPinMap[P] < 32) ? NRF_P0 : NRF_P1 )
#else
#define digitalPinToPort(P)        ( NRF_P0 )
#endif

#define digitalPinToBitMask(P)     ( 1UL << ( g_ADigitalPinMap[P] < 32 ? g_ADigitalPinMap[P] : (g_ADigitalPinMap[P]-32) ) )
//#define analogInPinToBit(P)        ( )
#define portOutputRegister(port)   ( &(port->OUT) )
#define portInputRegister(port)    ( (volatile uint32_t*) &(port->IN) )
#define portModeRegister(port)     ( &(port->DIR) )
#define digitalPinHasPWM(P)        ( g_ADigitalPinMap[P] > 1 )

void rtos_idle_callback(void) ATTR_WEAK;
/*
 * digitalPinToTimer(..) is AVR-specific and is not defined for nRF52
 * architecture. If you need to check if a pin supports PWM you must
 * use digitalPinHasPWM(..).
 *
 * https://github.com/arduino/Arduino/issues/1833
 */
// #define digitalPinToTimer(P)

// Interrupts
#define digitalPinToInterrupt(P)   ( P )

#endif // Arduino_h