1 files changed, 8 insertions, 7 deletions
diff --git a/Core/Src/main.c b/Core/Src/main.c
index 29fe9cf..67e6ab8 100644
--- a/Core/Src/main.c
+++ b/Core/Src/main.c
@@ -142,9 +142,10 @@ int main(void)
   /* USER CODE BEGIN WHILE */
   while (1)
   {
-    /* USER CODE END WHILE */
     HAL_GPIO_WritePin(IDLE_GPIO_Port, IDLE_Pin, GPIO_PIN_SET);
     __WFI();
+    /* USER CODE END WHILE */
+
     /* USER CODE BEGIN 3 */
   }
   /* USER CODE END 3 */
@@ -161,7 +162,7 @@ void SystemClock_Config(void)
 
   /** Configure the main internal regulator output voltage
   */
-  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
+  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE2);
 
   /** Initializes the RCC Oscillators according to the specified parameters
   * in the RCC_OscInitTypeDef structure.
@@ -181,10 +182,10 @@ void SystemClock_Config(void)
   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                               |RCC_CLOCKTYPE_PCLK1;
   RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_MSI;
-  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV2;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
 
-  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK)
   {
     Error_Handler();
   }
@@ -213,7 +214,7 @@ static void MX_SPI1_Init(void)
   hspi1.Init.CLKPolarity = SPI_POLARITY_LOW;
   hspi1.Init.CLKPhase = SPI_PHASE_1EDGE;
   hspi1.Init.NSS = SPI_NSS_SOFT;
-  hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_8;
+  hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
   hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB;
   hspi1.Init.TIMode = SPI_TIMODE_DISABLE;
   hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
@@ -252,7 +253,7 @@ static void MX_USART2_UART_Init(void)
   huart2.Init.Parity = UART_PARITY_NONE;
   huart2.Init.Mode = UART_MODE_TX_RX;
   huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
-  huart2.Init.OverSampling = UART_OVERSAMPLING_16;
+  huart2.Init.OverSampling = UART_OVERSAMPLING_8;
   huart2.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
   huart2.Init.ClockPrescaler = UART_PRESCALER_DIV1;
   huart2.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;