diff options
Diffstat (limited to 'ChibiOS_16.1.5/community/os/hal/boards/NRF51-DK/board.c')
| -rw-r--r-- | ChibiOS_16.1.5/community/os/hal/boards/NRF51-DK/board.c | 92 |
1 files changed, 0 insertions, 92 deletions
diff --git a/ChibiOS_16.1.5/community/os/hal/boards/NRF51-DK/board.c b/ChibiOS_16.1.5/community/os/hal/boards/NRF51-DK/board.c deleted file mode 100644 index c5237d7..0000000 --- a/ChibiOS_16.1.5/community/os/hal/boards/NRF51-DK/board.c +++ /dev/null @@ -1,92 +0,0 @@ -/* - Copyright (C) 2015 Fabio Utzig - 2016 Stéphane D'Alu / Bruno Remond - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#include "hal.h" - -#if HAL_USE_PAL || defined(__DOXYGEN__) - -/* RAM Banks - * (Values are defined in Nordic gcc_startup_nrf51.s) - */ -#define NRF_POWER_RAMON_ADDRESS 0x40000524 -#define NRF_POWER_RAMONB_ADDRESS 0x40000554 -#define NRF_POWER_RAMONx_RAMxON_ONMODE_Msk 0x3 - -/** - * @brief PAL setup. - * @details Digital I/O ports static configuration as defined in @p board.h. - * This variable is used by the HAL when initializing the PAL driver. - */ -const PALConfig pal_default_config = -{ - .pads = { - PAL_MODE_UNCONNECTED, /* P0.0 */ - PAL_MODE_UNCONNECTED, /* P0.1 */ - PAL_MODE_UNCONNECTED, /* P0.2 */ - PAL_MODE_UNCONNECTED, /* P0.3 */ - PAL_MODE_UNCONNECTED, /* P0.4 */ - PAL_MODE_UNCONNECTED, /* P0.5 */ - PAL_MODE_UNCONNECTED, /* P0.6 */ - PAL_MODE_OUTPUT_OPENDRAIN, /* P0.7 : SCL */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.8 : UART_RTS */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.9 : UART_TX */ - PAL_MODE_INPUT_PULLUP, /* P0.10: UART_CTS */ - PAL_MODE_INPUT_PULLUP, /* P0.11: UART_RX */ - PAL_MODE_UNCONNECTED, /* P0.12 */ - PAL_MODE_UNCONNECTED, /* P0.13 */ - PAL_MODE_UNCONNECTED, /* P0.14 */ - PAL_MODE_UNCONNECTED, /* P0.15 */ - PAL_MODE_UNCONNECTED, /* P0.16 */ - PAL_MODE_INPUT_PULLUP, /* P0.17: BTN1 */ - PAL_MODE_INPUT_PULLUP, /* P0.18: BTN2 */ - PAL_MODE_INPUT_PULLUP, /* P0.19: BTN3 */ - PAL_MODE_INPUT_PULLUP, /* P0.20: BTN4 */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.21: LED1 */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.22: LED2 */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.23: LED3 */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.24: LED4 | SPI_SEL */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.25: SPI_MOSI */ - PAL_MODE_UNCONNECTED, /* P0.26: XTAL (32MHz) */ - PAL_MODE_UNCONNECTED, /* P0.27: XTAL (32MHz) */ - PAL_MODE_INPUT_PULLUP, /* P0.28: SPI_MISO */ - PAL_MODE_OUTPUT_PUSHPULL, /* P0.29: SPI_SCK */ - PAL_MODE_OUTPUT_OPENDRAIN, /* P0.30: SDA */ - PAL_MODE_UNCONNECTED, /* P0.31 */ - }, -}; -#endif - -/** - * @brief Early initialization code. - * @details This initialization is performed just after reset before BSS and - * DATA segments initialization. - */ -void __early_init(void) -{ - /* Make sure ALL RAM banks are powered on */ - *(uint32_t *)NRF_POWER_RAMON_ADDRESS |= NRF_POWER_RAMONx_RAMxON_ONMODE_Msk; - *(uint32_t *)NRF_POWER_RAMONB_ADDRESS |= NRF_POWER_RAMONx_RAMxON_ONMODE_Msk; -} - -/** - * @brief Late initialization code. - * @note This initialization is performed after BSS and DATA segments - * initialization and before invoking the main() function. - */ -void boardInit(void) -{ -} |